What to do when boredom ensues?...

[TAKTAK]

...dismantle your eeePC of course!!


some may allready have seen this... but might aswell post it on here too

first off.. sorry about the crud pictures (don't have a proper camera so just using my phone...)
secondly... i hold no responsibility if you b0rk your eee by following this... tis done under your own risk..

lets begin:

first up is just a piccy of the awaiting eee...


so the first real step is to turn her over and undo her buttons (ooh er matron)
just remove the battery, unscrew all six screws from the base, and then unscrew the access plate aswell


after doing that and removing the plate you will be left with:


now, flip her over and open her up.
at the top of the keyboard there are 3 clips, press all three back and the keyboard should just come free from the plate (don't yank it tho... cos the cable is still attached )


the aforementioned keyboard cable...


to disconnect the cable just slide the two clips (thats are either side) up, and the cable will gently pull out


now.. set the keyboard to one side (with the screws that you should have set aside )
and you may notice that the touchpad also needs disconnecting... it is much the same as the keyboard connection.. so just slide the little bar that locks it in place forward, and then gently pull on the blue tab.


et voila, the front is done...

[TAKTAK]

now... to remove that top plate

remove all of the screws from the plate (there is a screw under the warranty sticker)

set them to one side (you'll need them later )

push a screw driver in through the front and pry open the case... (there are two clips along the front near the trackpad, don't worry if you cath the button, it just pops back on)


next, turn the eeePC around and do the same (its harder to get the screwdriver into position and there are three clips along the back...


now... gently pry all of the edges up and lift the plate to about 40 degrees, then slide the top plate sideways (just so that it can get past the audio ports..)
and it should pop off.. if it doesn't want to come off check that you have removed all of the screws...
note that the top plate is essentially the heatsink...


now you get to see the top of the mobo and the proccy, thermal pads etc, etc


disconnect both wires in the top corner (speakers and webcam)


then disconnect the fan...


next it's the video connection that gets pulled...


remove the rubber bung from the modem port... just give it a push with the screwdriver (it gets in the way of removing the motherboard...)

[TAKTAK]

time to remove the motherboard...
at the bottom there are two tabs holding the mobo in place... just lever the mobo out..



now give the motheboard a bit of a wiggle and it should come out (you need to tilt it to get the usbs out.)
now... hold off from just yanking it as the atheros wireless card is connected underneath...


just pull both wires off the micropci card and then the board will just come free...



here you can see the SSD that the eee uses (in this case 4GiB [4 * 1 GB chips])


here you can see the bottom section of the case


closeup of the ickle fan

[TAKTAK]

right... so that concludes the disassembly that i am doing tonight... (tis getting late.. and theres not much point with rubbish quality piccys...)

but.. you don't think i would just leave you right?

time to reassemble...

and for those of you that can't follow instructions backwards...

put the motherboard back in place like so (making sure that you connect the atheros wireless adaptor, and the wires aren't in the way of any screws... otherwise you'll be taking it apart again ):


now.. reconnect the cpu fan, webcam, vga, and speakers again ensuring that the wires don't get in the way of any screws...


now to put the top part of the case back on
make sure that the thermal pads are in place (one of mine is slightly damaged after catching it...)
and then lower the top plate on at an angle (so that the lefthand edge can get over the audio and mic connection)
press down all of the edges so that it is held in place with the plastic clips.
now screw the top plate back on...


now it's time to reconnect the trackpad, push the cable in (ensure that it is right in...) and then close the locking mechanism.
do the same with the keyboard, push the cable right in (to ensure a full connection) and close both tabs.


now to lock the keyboard down again...
note that on the bottom of the keyboard there a some ridges... place these into the top plate first and then lower the top edge and press down, so that the 3 clips engage again, thus holding the keyboard in place again...


now.. turn it upside down again...
put the flap back in and screw all of it up.


so... now it's complete again... so does it boot after fiddling?

the answer?

of course it does!!


i leave you with a compiz cube


[edit]better add this...

to enable full desktop connect to tinternet..
press 'alt+t' to bring up the terminal
type 'sudo su' and hit enter
now type 'apt-get update' hit enter
type 'apt-get install kicker ksmserver' hit enter
and tell it to install without prompts when it asks... (type 'y' and hit enter)
go into the settings tab, go into settings and tick always boot into full desktop... and done...

and if you want to install compiz then add some repositories and install it using apt, then edit the config using nano, so that you get rid of the horrible black bars...
[/edit]

edit: one thing i should add... enabling full desktop that way causes the system to double boot, it boots into easymode for a split second and then reboots to advanced everytime..

a quick google search for eeepc double boot will suffice, but the process could leave you having to do a restore (editing startupfull.sh and startupsomething.sh[mind blank, don't shoot me :P]) (hence i'm not saying how to)

[TAKTAK]

I havn't accidentally double posted... honest...

erm... this was actually going to be....a... erm...

link to the hexus news item(?): http://www.hexus.net/content/item.php?item=15261

edit: infact, i will make this an informative post...




...





^^part one^^

\/\/Part 2\/\/

[TAKTAK]

following on from the first session, some of you may know, that i have decided to mutilate the little beauty and make few improvements...

the most noticeable and the focus of this thread is the touchscreen...

and this time the pictures are crystal clear... honest they are... if they look blurry to you then you may need yours eyes checking

okay... so i lied... they are probably worse this time around...



and hey ho, away we go again:

first up (as last time) is a picture of the sacrificial lamb:


secondly is the touchscreen kit (the controller and the overlay):


as mentioned above... here is the control board:


and here is the overlay...:




now... to do the same as last time...

flip her over and undo her buttons :naughty:...:


remove the keyboard same as last time:

first the little tabs:


then the cable:


now disconnect the trackpad:


undo all of the screws in the heatsinky/keyboard holdy/thingy ma bob:


remove the plate by lifting and prising:


now you should have a pile of bits, if you havn't then your doing it wrong...:


here you can see the thermal pad terror that i inflicted in the last rendition:

[TAKTAK]

now, time to get to the monitor:

underneath these:



there are some screws... they need to be undone...


again you need to prise it apart to get into it:


then, once inside you get a glimpse of the loverlyness:


teh webcam:


teh speakers:


teh growing pile of removed bits...:



now... to make some room for the touch panel... we need to remove the gubbins and the monitor of course...:
to remove the monitor, unscrew the lower circuit board and then disconnect the monitor...




now remove the aforementioned gubbins:




the blind eee:


now, we need all the room we can get so remove the metal frame:



the pile grows...:

[TAKTAK]

now... the control board connects via USB... sooooo, the easiest way seeing as though i dont use the webcam?:


is disconnect the webcam and splice the two cables...:


this is where i am planning on putting everything...:


so some plastic needed hacking off:



the de-plasticated control board


the awaiting splice:


and while im waiting to splice the cable i might aswell partially re-assemble and use....:




the partial rebuild also eliminates my fears that i had broken the backlight...

thus concludes the current stage.......
such a lovely place to leave it for the time being :P


and a month on.... it is still like that because i need to rustle up my soldering iron

[gilgamesh]

A cool guide there mate, keep up the good work pal


gilgamesh

Nice! Can't decide whether to get an eee or not... Liking the idea of the touch screen tho